We are still progressing on our R35 GT-R harness bar and the second revision will be tested for the first time in another customer’s car at Laguna Seca on Thursday.  This newest revision should make the installation of the harness bar itself even easier for owners at the track and we can’t wait to test it out.  It should be installed by early afternoon today.  As before, we are holding off on showing pictures of the bar until it is ready to be fully released.  Hang in there friends.

Getting back to the ZCG GT-R… The car is still at SSP as it seems they have run into some issues when the car hit the 700wtq mark.  I’m still waiting to hear more on the situation and I will update you when I find out.

We also received a set of COBB Tuning sway bars for our car when it comes back from SSP.  They are high quality bars with two levels of adjustment for the front and three for the rear.  These will be put on as soon as possible because we have a few track days planned for this car as well in the near future.  It will be interesting to see how these change the handling characteristics of an already amazing car.

Fresh in from Japan are the five sets of Panasport 3 piece lightweight wheels that were ordered for the on-going RB project cars.  We are now one step closer to making all the cars rollers.  As you can see from the photos there are three black sets and two silver.  The craftsmanship and appearance are going to suit these highly modified 240Zs perfectly.

These wheels are ordered in a custom offset just for Z Car Garage and will allow us to fit as much as a 255/40/R17 tire without flaring the fenders.  With the large diameter of these wheels the cars will need to receive coilovers because the stock spring and strut combo intrude fairly deep into the wheel well, of course this will be getting done anyways to allow us to change the spring rate to best suit the new drive train and the owners requirements.

As soon as a tire choice is made and we get them mounted on a car you should expect to see some more pictures of these works of art.  There are some more pictures after the “read more.” Enjoy

…[read more]

The VQ35HR engine in the ’07-’08 350z just continues to impress us here at Z Car Garage.  This last generation of the VQ35 responds so well to bolt on modifications that the sky is the limit when it comes to producing normally aspirated horsepower.  Yesterday we bolted on another Injen intake system and an Unorthodox Racing pulley to accompany the Nismo exhaust that was already installed on this customer’s car.

The Injen intake now grabs air from in front of the radiator almost directly in the high pressure air stream.  The quality and appearance of the intake is top notch and fit and finish is up to the standards of a company that has been around as long as Injen.  The pulley from Unorthodox Racing is a high quality piece machined out of aluminum and is supposed to weigh around seven pounds less than the stock piece (8.25 vs 1.32lbs.)  We actually weighed both pieces and found the stock pulley on this HR to weigh only 4.8lbs, go figure.  Maybe they had two on the scale?  Anyways, the pulley is the stock diameter so all benefits come from reduced rotational mass rather than an under-drive system.

They dyno results were right were we expected them to be, but that doesn’t make them any less amazing!  While the main horsepower gain comes on the top-end, there are notable gains throughout the mid-rage on the torque side of the equation.  From looking at the graph you will also notice that the modifications cause the torque curve to not drop off as quickly past 5,500 rpm.  The car now makes twelve more foot-pounds of tourqe at peak horsepower, you will certainly feel that in your butt dyno!

Since the two modifications were carried out at the same time I can’t say for sure how much of a difference the crank pulley alone made, but if you look back at the first Injen intake we did on an HR you will see what the intakes did by themselves on that car.  I know, different day, different car,  but can be used as some sort of a comparison.

We are patiently waiting to see more aftermarket suppoort for the HR engines to see what sort of power we can extract.  I want to see cams, intakes, new headers, and more ideas that I’m going to save for our shop to make.  Hopefully more is on the horizon.

A very good customer of ours was involved in an unfortunate accident which ended with his pristine 300zxtt getting totaled.  As you can see from the pictures the car was rear ended at a high rate of speed.  The good news to come out of this is that he is uninjured for the most part and that there are A TON of good 300zx parts that are now up for sale.

This car is being fully disassembled right now and as you can see we are just about ready to pull the engine and transmission.  The interior has already been removed for the most part and has been carefully put away until it finds a new home.  You can get a complete list of the parts that are for sale by emailing us at rob@zcargarage.com.

There are a few more pictures of available parts after the the “read more.”

…[read more]

Happy Monday to everyone!

Today we are putting the finishing touches on the 3.8L 350z with the GReddy twin turbo kit and I am getting very anxious to take that beast out on the road.  All that is really left is some fine tuning on the Haltech EMS.  On the initial rundown and test drive the fuel map turned out to be quite rich and needed a touch up in the mid-range.  Even with the rich condition, the car is very powerful and has immense amounts of low-end torque.  I don’t have any dyno figures yet because we are updating our Dynojet hardware to make sure that everything is as new as it can be to give our customers the best and most reliable results.  We’ll have to settle for street tuning until the new dyno tower arrives.

Also on the war path for today is the red 280ZX restoration car.  I’ll be picking up the newly dyed interior pieces a little later today and the car should really start flying together.  This project has been with us for a very long time and it’s going to be a little strange once it all comes together.  I washed it this morning and ended up standing there admiring all the work and time that we’ve put into it.  It’s really a special car and we can’t wait to deliver it to the owners.

I have a few more things to fill you in on so check back a bit later in the day!